Can I Set Up A Bathtub Myself?
Can I Set Up A Bathtub Myself?
Blog Article
What are your ideas with regards to Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a new one is also a moderately difficult project. If the old tub is readily accessible, the project can move quickly; if you need to open up a wall surface to get rid of the old bathtub and also place the new bathtub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also embeded in the brand-new one. Make certain you have qualified on your own for the task as well as are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed job, it is much better to consider utilizing one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will help you mount a new bathtub in your washroom if you have already acquired a new bathtub as well as don't need to transform the plan of your previous supply of water pipes.
Your devices and also material checklist need to consist of the following:
Planning for the Setup
First of all, the supporting structure supplied with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing taps can be rather bothersome as a result of the restricted access that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric all set for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Using the two wooden boards under its feet, place the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill the bath tub as well as also check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the tub ought to wait till the tub has been made use of a minimum of once as this will resolve it right into its last position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The former type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that report on Installing A Bathtub from a friend on a different web address. Are you aware of another individual who is inquisitive about the niche? Take a moment to share it. I praise you for your time. Visit again soon.
Detail
Report this page